Defecting

FEATURED PRODUCTS

ACTIVA [ACS18] - 18" CUT OFF SAW C/W 10' INFEED AND OUTFEED CONVEYOR WITH POP UP STOPS...

DIMTER [OPTIMAT 304] - OPTIMIZING CUT OFF SAW...

OLIVER [2694-8] - OPTIMIZING CUT OFF SAW...

GRECON [9004] - OPTIMIZING SAW...

Page 1 of 4

<< First Page | < Prev. Page | Next Page > | Last Page >>

ACTIVA [ACS18] - 18" CUT OFF SAW C/W 10' INFEED AND OUTFEED CONVEYOR WITH POP UP STOPS

Inventory #20789

Capacity 18" undercut chop saw, maximum working width 10-330 mm (.5"-13"), max. working height 10-100 mm (.5"-4"), the cutting size will be a combination of the two sizes.

The higher the cut...

View Specifications >

		Learn about Machines of Interest to Me >

ACTIVA-ST [ACS18T] - 18" CUT-OFF SAW

Inventory #22083

Capacity revolution of saw arbor 3320/3180 RPM (60/50 Hz).

Saw blade 1" x 18" x 3.4 mm x 120 T.

Driving motor 7 1/2 HP.

Table size 690 mm x 660 mm.

Level height of table 840 mm...

View Specifications >

		Learn about Machines of Interest to Me >

DIMTER [304 R OPTI CUT] - OPTIMIZING SYSTEM COMPLETE WITH INFEED SYSTEM & MARKING STATION

Inventory #18122

SOLD	Capacity three (3) marking stations with roll cases including custom scissor lift system for markers to work from. Elevated pass line off floor. MSL lateral infeed system for 16...

View Specifications >

		Learn about Machines of Interest to Me >

DIMTER [OPTICUT S-90] - OPTIMIZING CUT-OFF SAW

Inventory #23305

Capacity 4" thick x 9" wide maximum, minimum 3/4" x 1" wide incoming board.

Highly accurate push feed saw.

Right-hand version (material feeds from right-to-left).

16" minimum to 14-3...

View Specifications >

		Learn about Machines of Interest to Me >

DIMTER [OPTIMAT 304] - OPTIMIZING CUT OFF SAW

Inventory #21590

Width capacity 8" maximum and 1-1/2" minimum.

Thickness capacity 1/2" to 3" max.

Board length from 20" to 20'.

Outfeed parts as short as 5".

Infeed marking station double sided...

View Specifications >

		Learn about Machines of Interest to Me >

GRECON [9004] - OPTIMIZING SAW

Inventory #21364

Capacity 3 meter infeed grading table.

Outfeed conveyor consisting of 7 kickers.

Machine recently was rebuilt servo motor, new feed belt, rubber top chain and many new parts.

Many...

View Specifications >

		Learn about Machines of Interest to Me >

GRECON/DIMTER [OPTICUT 104/2] - OPTIMIZING CROSS CUT SAW WITH DEFECTING

Inventory #21615

Capacity for working zize in width 40 - 300 mm.

In thickness 15 - 100 mm.

Infeed cross belt.

Pusher 6000 mm long with length and defect reading.

Up stroke saw 500 mm diameter...

View Specifications >

		Learn about Machines of Interest to Me >

INDUSTRIAL [0500] - UP CUT SAW

Inventory #19572

Capacity 2-3/16" x 8-1/4" cap.

14" blade cap.

Left-hand unit feeding from right to left.

5 HP motor.

(5 - 90) cycles/min.

Equipped with: magnetic starter with low Voltage...

View Specifications >

		Learn about Machines of Interest to Me >

KITCAM - FENCE WITH FLIP STOPS

Inventory #11245

SOLD	Capacity fence with built in tape measure. 1 flip stop on each side. 8' on one side. 12' on the other side. Heavy duty stops 1" x 3" aluminum plate. Guage bar 1" x 1" steel...

View Specifications >

		Learn about Machines of Interest to Me >

KITCAM [KNA 1200] - RIGHT HAND CHOP SAW

Inventory #11817

SOLD	Capacity working height 36". Cut off capacity 2" x 12". 7.5 HP. Magnetic type starter. 3 V-belts drive. 1" arbor for blade and 1-1/4" for bearings. Air pressure 60 PSI...

View Specifications >

		Learn about Machines of Interest to Me >

Page 1 of 4

<< First Page | < Prev. Page | Next Page > | Last Page >>

* Price may vary with exchange rate.