Online Catalog - Edgebanders - Single Over $20,000 (U.S.)

Site Languages:

Credit Cards Accepted:

FEATURED PRODUCTS

HOMAG [OPTIMAT KL 77/A3/S2] - EDGEBANDER WITH PRE-MILLING...

SCM [SELECTA 12] - SINGLE SIDED EDGEBANDER WITH CORNER ROUNDING...

BIESSE [STREAM B1 8.5] - 3MM SINGLE SIDED EDGEBANDER WITH CORNER ROUNDING...

Page 1 of 1

<< First Page | < Prev. Page | Next Page > | Last Page >>

POLYMAC [ERGHO 3] - EDGEBANDER

Inventory #17595

Capacity heavy steel plate construction structured for max. rigidity.
Variable feed speed chain (29-59 FPM) with non-skid rubber support pads.
Sound enclosure.
Front & back end trimming station.
Top and bottom rough trimming station.
Top and bottom trimmers powered by 1.0 HP motors.
3 mm cutters included with top and bottom trimmers.
PVC scraping station.
Top and bottom buffing station for smoothing PVC...

View Specifications >

		Learn about Machines of Interest to Me >

ACTIVA [AEB4HD] - 3 MM PVC SINGLE SIDED EDGEBANDER WITH END TRIM, TOP BOTTOM FINE TRIM, SCRAPING AND BUFFING

Inventory #20715

Capacity end trim.
Top and bottom fine trim.
Scraping and buffing, PLC controlled, 200 Hz electronic frequency converter, .4 - 3 mm band thickness.
Maximum width of edgebanding 3 mm x 60 mm high, panel thickness 10 mm - 60 mm, minimum panel width 80 mm (3.5"), 4 kg bottom mounted glue pot.
Edgebanding coil feeds automatically to a maximum of 3 mm thick through a high powered guillotine, 5 roll pressure section, workstations include double motor end trim 0.35 kW (1/2 HP) at 12,000 RPM each, top and bottom fine trimming 0.7 kW (1 HP) at 12,000 RPM, top and bottom scraping unit with pressure disk to avoid damaging the material with air blowers to remove residue, top & bottom buffing unit which tilts 0° - 5° with air cleaning, 3 HP variable feed speed 12-40 M/Min (40-130 Ft/min.), double rubber roller pressure beam, automatic panel thickness protection, supplied with remote control jogging switch for ease of set up, C/W sound enclosure and outboard control panel...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [STREAM B1] - SINGLE SIDED EDGEBANDER

Inventory #21356

Capacity with following groups: pre-milling units, glueing unit, (6) edge loaders, endcutters, rough trimmers, fine trimmers (radious R 1/2/3), rounding groups with 4 motors, moulding unit, edge scrapers, glue scrapers, oscillating brushes.
Electronic control of the operating groups.
Variable feeding speed.
Motorized positioning of top bar.
Automatic motorized introducer of the panels.
Sound-proofed booths.
CE normatives...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [SE 7400] - 4MM SINGLE SIDED EDGEBANDER

Inventory #22754

Capacity 0.4 - 20 mm (3/4") thickness.
70 mm min. panel width.
Equipped with automatic edge feed magazine for coil.
HPL and strip stock.
Hot melt glue system with reversible glue roller applicator and hopper fed glue pot.
Pneumatically controlled pressure roll section.
Double motor front and rear end trim with 4 position turret adjustment for changing from straight to chamfer cuts (1.4 HP each motor) Top and bottom rough trims (2 HP each motor).
Top and bottom fine trims tiltable 0 to 30°s (0.5 HP each motor).
Top and bottom buffing unit (two 0.33 HP motors).
Scraping and buffing stations.
Top pressure beam with double V belts, 80 mm wide heavy duty feed chain with rubber pads.
Feed speed variable up to 35 MPM, lower chip conveyor C/W SIKO digital adjustments on T and B flush fine trim.
15 KVA 300 Cy frequency converter, outrigger panel support, insulated sound cabins with interior and overhead lighting for all trim workstations.
Gravity return conveyor and Siemens frequency inverter for trim stations...

View Specifications >

		Learn about Machines of Interest to Me >

ACTIVA [AEB5] - 3 MM PVC AUTOMATIC EDGEBANDER END TRIM, ROUGH TRIM, FINE TRIM, SCRAPING AND BUFFING

Inventory #23150

Capacity thickness of edgebanding 0.5-3 mm.
Working thickness 11-40 mm.
Minimum width 90 mm.
Working length 280 mm.
1st unit guillotine end trim.
2nd unit top and bottom rough trim 0.5 HP at 12000 RPM.
3rd unit top and bottom fine trim 370w.
4th scraping.
5th unit buffing 90w.
Glue pot 1250w.
Glue pot maximum temperature 200° c.
Track motor 370w.
Edgeband drive motor 25w.
Glue pot drive motor 40w.
Configuration hot melt, end trim, rough trim, fine trim, scraping and buffing.
Glue type hot melt...

View Specifications >

		Learn about Machines of Interest to Me >

ACTIVA [AEB6] - 3 MM PVC AUTOMATIC EDGEBANDER PRE-MILLING, END TRIM, ROUGH TRIM, FINE TRIM, SCRAPING AND BUFFING

Inventory #23614

Capacity thickness of edgebanding 0.5-3 mm.
Working thickness 11-40 mm.
Minimum width 90 mm.
Working length 280 mm.
2 pre-milling heads.
Guillotine end trim.
Top and bottom rough trim 0.5 HP at 12000 RPM.
Top and bottom fine trim 370w.
Scraping.
Buffing 90w.
Glue pot 1250w.
Glue pot maximum temperature 200° c.
Track motor 370w.
Edgeband drive motor 25w.
Glue pot drive motor 40w.
Configuration pre-milling, hot melt, end trim, rough trim, fine trim, scraping and buffing.
Glue type hot melt.Optional extra all Italian high speed motors extra US$5,000...

View Specifications >

		Learn about Machines of Interest to Me >

SCMI [OLIMPIC K203-R] - SINGLE SIDED EDGEBANDER WITH CORNER ROUNDING

Inventory #24826

Capacity 8 mm.
Min/max panel thickness 5-55 mm.
Min. length work piece 140 mm.
Min. panel spacing 20".
Edge scraper.
Corner rounder.
End trimming.
Large capacity granulate glue pot with 10-12 minute heat up time.
Automatic strip magazine.
Pneumatic positioning of scrape unit.
Digital inverter provides electronic motor braking.
Orion 200 graphic controller, capable of storing 100 programs.
Two motor corner rounding unit capable of trimming entire panel changes from 3 mm to thin tape through controller...

View Specifications >

		Learn about Machines of Interest to Me >

SCM [SELECTA 12] - SINGLE SIDED EDGEBANDER WITH CORNER ROUNDING

Inventory #25043

Capacity 12 mm edgebanding thickness.
Control panel on infeed.
Front & rear end trimming units.
Top & bottom rough trimming units.
Top & bottom fine trimming units.
(2) motor profile trimming units.
3 mm scraping unit.
Top and bottom buffing units.
Heat activation unit.
PLC controls...

View Specifications >

		Learn about Machines of Interest to Me >

SCM [BASIC 2 AUTO] - EDGEBANDER

Inventory #25058

Capacity Auto Feed magazine for edge strips.
Auto loader for rolled edges.
Shear device for coiled material with thicknesses up to 1.2 mm.
Glue pot unit.
Horizontal pressure unit.
End cutting unit with (2) independent motors.
Trimming unit tiltable from 0 to 15°s with cutters.
Top and bottom buffing unit.
Acoustic safety enclosure...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [STREAM B1 8.5] - 3MM SINGLE SIDED EDGEBANDER WITH CORNER ROUNDING

Inventory #25177

Capacity glue pellet station with 6 edge in feed table.
End trimmers top / bottom.
Rough trim top / bottom.
Finish trim plus 2 extra motors with 3 mm radius cutters.
(4) Station corner rounding.
3 mm round free station inside enclosure.
Top / bottom for radius scraping.
Edge top / bottom glue scraper.
Top / Bottom buffing.
Top / Bottom hot air.
(6) Magazine edge roll holder.
(4) Outboard stands for stock support.
Includes additional parts and attachments.
Options included, transfer infeed table, return table, barcode applicator, sound enclosure...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [OPTIMAT KL 74/A3] - SINGLE SIDED EDGEBANDER

Inventory #26211

Capacity work station: double motor front and rear end trim.
"HL 81 Chamfer/Straight" (0.81 kW.
200 Hz.
12000 RPM).
Top and bottom flush trim units (1.5 kW.
200 Hz.
12000 RPM).
Top and bottom bevel & radius trim.
(0.4 kW.
200 Hz.
1200 RPM).
Tiltable 00 - 300 from operator panel.
Minimum workpiece width 55 mm, panel thickness 12 - 60 mm, panel overhang 30 mm.
W/power pack up to 35 m/min.
Double automatic magazine for PVC.
Double polish units motor (0.25 kW).
"QA 34" Hot melt glue system w/pre-melting hopper feed.
Heated glue applicator.
Line control with HOMATIC "NC 21" controller w/PLC storage, 80 mm wide Heavy Duty feed chain w/rubber pads, automatic chain track lubrication system.
Top pressure w/rollers 2 rows, manual height adjustment with digital position read-out...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [ERGHO 5] - SINGLE SIDED EDGEBANDER UP TO 15 MM EDGING

Inventory #26268

Capacity for panel thickness from 10 to 45 mm.
Edge thickness in coil from .4 to 3 mm and in strip up to 15 mm.
Maximum strip size 15 mm X 45 mm.
Minimum panel width 85 mm with 150 mm in length.
2 speed feed 10 and 20 meter/min.
Glue pot with 3 liters capacity.
Pressure zone with 4 rolls.
End trimming unit.
Rough trimming unit.
Fine trimming unit.
Edge scraping unit.
Edge heating device.
Buffing unit.
Sound enclosure.
All motor with high frequency 200 Hz...

View Specifications >

		Learn about Machines of Interest to Me >

FLETCHER TOLBERT [FM-45EB] - SINGLE SIDE EDGEBANDER

Inventory #26736

Capacity End trim top & bottom.
Side trim top & bottom.
Grooving Saw.
Sanding.
Buffing station top & bottom...

View Specifications >

		Learn about Machines of Interest to Me >

BRANDT [KDN 340] - 3MM EDGEBANDER WITH SCRAPING / BUFFING (SINGLE PHASE)

Inventory #26836

Capacity 4-3 mm (1/8") Edge thickness.
8-45 mm panel thickness.
60 mm min. panel width and 140 mm min. length.
Equipped w/infeed heating shoe to pre-heat panel edge, hot melt granulate glue system w/fast start-up.
(10-12 min. heat up) w/reversible rotation glue applicator roller & automatic reduction glue temperature adjustment (when idle drops to 150°s it takes 2-1/2 min. to re-activate).
3 mm PVC pneumatic guillotine for coil cutoff.
Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine.
2 roller pressure section (1st driver, 2nd idle) with electronically controlled & feed speed synchronized drive roll.
Workstations: vertical travel double motor front & rear end trim with 0-15° horz. bevel cap (.25-12,00 RPM motors).
Top & bottom flush/bevel trimmers (.35 HP - 12,000 RPM motors) bevel 0-15°s.
Top & bottom PVC scraping unit for up to 3 mm radius.
Last station: top & bottom buffing unit (.15 HP - 2,750 RPM motors).
Feed speed of 30 FPM - equipped w/ operator control panel at eye level, automatic height adjustment w/top pressure beam for all workstations, electronic line control (no limit switches) digital height indicator on hold down beam, electronic motor brakes on trimmers...

View Specifications >

		Learn about Machines of Interest to Me >

BRANDT [KD 66/2 OPTIMAT] - 8 MM PVC EDGEBANDER

Inventory #27073

Capacity Edgebander thickness: 0.4 - 8 mm.
Coil cutoff max. 0.8 x 45 mm 3 x 45 mm (PVC).
Edgeband height 12 - 45 mm (1/2" - 1-3/4").
Panel width min. 160 mm (6-3/8").
Panel thickness min. 8 mm (5/16").
Feed speed 11 m/min. (36 FPM).
Feed motor 2.2 kW (3 HP).
Pressure section first roller driven, Two rollers idle.
End trim unit two motors .27 kW (1/3 HP each).
Cutting speed 12,000 RPM.
Straight cut max. 5 x 45 mm (3/16" x 1-3/4".
Fine trimming unit .40 kW (1/2 HP each).
Tilting range 0°s - 15°s.
Cutter speed 12,000...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [KAL 310/5/A20] - 3MM EDGEBANDER WITH OPEN SPACE FOR PRE MILLING

Inventory #27441

Capacity working level 950 mm (37-13/32"), min. working width w/thickness 22 mm (7/8") 55 mm (2-5/32"), 60 mm (2-3/8") 100 mm (3-15/16"), panel overhang 30 mm (1-1/8"), workpiece thickness min. 12 mm (15/32"), max. 60 mm (2-3/8"), edge thickness strips 0.4 mm to 20 mm (0.16" to 25/32"), coils 0.3 mm to 3 mm (0.12" to 1/8"), processing limits strips 1150 mm2 (1.78 sq. in), coils 135 mm2 (0.19 sq. in).
Open Space for the later addition of a pre-milling unit.
{Panel Pre-Heater Homag Unit #2325, quartz lamp for heating substrate edge before glue application, for improved edge quality and optimum bonding.
Preparation for adaptation of Nordson application unit, provides mounting assembly for Nordson Slot Nozzle, glue reactivation system.
Nordson Glue Application System, per Nordson proposal 04081Q-64-411, BN-20.
5-gallon pail un-loader, EB60V-III 10 to 60 mm (13/32" to 2-3/8") adjustable edge banding slot nozzle.
Multi-Purpose Magazine with Single Coil Horizontal Table, Homag Unit #2999, capable of running coiled material, strips.
And solid wood bands, easily changed from one application to the next with the flip of a switch, conveniently located on the movable control pendant, infeed angle 8°s, edge thickness 0.4 mm to 20 mm (0.016" to 25/32"), edge height 12 mm to 65 mm (15/32" to 2-9/16"), processing limits 900 mm2 (1.39 sq. in), min. edge length 260 mm (10-1/4"), strip capacity approx. 295 mm (11-1/2").
Clipping Unit Homag Unit #2445, designed for today's popular use of thick coil PVC, for use with single-roll table magazine, max. edge thickness 3.5 mm (0.14"), max. edge height 65 mm (2-9/16"), PVC processing limits 135 mm2 (0.19 sq. in.), veneer processing limits 100 mm2 (0.15 sq. in.), max. roll diameter 900 mm (35-7/16").
Magazine Height Adjustment Homag Unit # 2451 , with threaded spindle adjustment and digital readout, adjustable +/- 5 mm (+/- 13/32").
Pressure Zone for Gluing Section Type G Homag Unit #2507, one (1) driven pressure roller 160 mm (6-5/16") diameter, twelve (12) secondary pressure rollers 70 mm (2-3/4") diameter, with pneumatic pressure control for straight edges, centralized manual adjustment for edgeband thickness with digital mechanical counter.
Snipping Unit WK14/0, 8 kW Solid Wood Homag Unit# 3064, for snipping the edge overhang at front and rear edge, upright snipping stop, installed above the machine frame - thus no snipping waste in the snipping unit, workpiece overhang manually adjustable, motors swiveled manually for chamfer snipping, manual adjustment of the snipping stop to different edge thickness, two (2) motors each 0.4 kW, 200 Hz,,12,000 RPM, workpiece overhang min. 30 mm (1-1/8"), edge thickness chamfer / straight max. 3 mm (1/8"), chamfer max. 30°s, snipping depth soft max.20 mm, edge width 65 mm (2-9/16"), edge cross section max. 1000 mm2, feed speed max. 25 m/min., panel distance min. 350 mm, panel sequence front edge/front edge, 25 m/min. (82'/min.) = 1000 mm , panel thickness max. 60 mm, the unit is installed at the machine frame above.
Top / Bottom Flush Trimming Unit Homag Unit #3209, motors positioned one above the other, 1.5 kW.
200 cycle; 12,000 RPM, angle adjustment +/- 1°, with two (2) carbide tipped trimming cutters, 70 mm x 25 mm (2-3/4" x 31/32"), HSK 25, z = 4, motors running against direction of feed, motors manually adjustable with digital mechanical counters, height adjustment with top pressure beam, electronic frequency inverter for control of motor speed and braking, HSK 25 tool interface, motors running with direction of feed.
Latest computer, monitor and modem recently installed.
Homatic PC 22 2 GHz CPU...

View Specifications >

		Learn about Machines of Interest to Me >

IMA [NOVIMAT CONCEPT/2425] - SINGLE SIDED EDGEBANDER

Inventory #27638

Capacity Left-hand machine.
IMATRONIC 121/01.
Electromotorical height adjustment of the top pressure.
Joint milling unit.
Jointing cutter head with turnover knives.
Milling unit.
Self-tracing scraper.
Bevel sanding/buffing unit.
Oscillating Edge sanding unit.
Flush milling cutter with turnover knives.
Min. panel width 65 mm.
Fix panel overhang beyond chain track 38 mm...

View Specifications >

		Learn about Machines of Interest to Me >

BUSELLATO [FLEXA 256] - AUTOMATIC SINGLE SIDED EDGE BANDER WITH CORNER ROUNDING

Inventory #27746

Capacity Pre-arranged for pre-milling unit.
3 mm Shear.
Heating lamp for panel edge.
Strip or coil feed.
Hot melt glue tank.
End trimming units.
.5 kW Motors with automatic blade inclination.
Top & bottom rough trimming units 1.8 kW motors.
Top & bottom finish trim units .5 kW motors.
Corner rounding units .35 kW motors.
Edge scraping unit.
Top & bottom scraping unit.
Top & bottom buffing .12 kW motors...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [STREAM B1 9.5] - EDGEBANDER WITH PRE-MILLING AND CORNER ROUNDING

Inventory #27762

Capacity panel overhang (fixed) 35 mm.
Panel thickness 10 - 60 mm.
Chain advance speed 10 to 24 mt/min.
Work table height 950 mm.
Panel working width 100 to 3200 mm.
Panel length 150 to 3200 mm.
Multiple axis numerical control with Windows type video interface, control of positioning axes (machine set-up), adjustment of feed chain speed,,adjustment of presser height according to the thickness, management of edge strip exchange device.
Management of machining list, cascade type motor start up, management of diagnostics.
Motorola 6803D microprocessor with 2 Mbytes flash disk, 6 Mbytes static RAM.
4 RS232/485 serial ports.
NC410 controller with12" LCD colour monitor.
IP54 keyboard, 1.44 Mb floppy-disk drive, mouse system.
RT63 pre-milling unit with (2) 3.5 kW motors.
SP20 Gluing Unit with pre-melting device,capable of strips up to 20 mm thick or coils up to 3 mm thick.
Pressure area consist of (1) driven 180 mm diameter roller and (6) 75 mm idle rollers.
NC Y axis for presser section, includes motorised edge banding strip presser section drive and relative NC management.
IT45 end-trimming unit with (2) 0.65 kW motors.
RS10 rough milling unit with (2) 2.4 kW motors.
RF30 fine milling unit with (2) 0.65 kW motors.
AR10 top/bottom corner rounding unit with (4) swinging 0.3 kW motors.
FB30 universal milling unit with 5 kW motor.
RB30 edge scraper unit.
SZ30 superimposed oscillating buffers unit with (2) 0.18 kW motors.
PH10 edge heater.
LO10 horizontal edge sanding unit for sanding of the flat part of the edge...

View Specifications >

		Learn about Machines of Interest to Me >

BRANDT [KDN 630 OPTIMAT] - AUTOMATIC 12MM EDGEBANDER

Inventory #28155

Capacity 0.4 to 12 mm banding.
PC LCD controller.
Integrated electronic line control system for increased reliability and diagnostic assistance.
No limit switches used for setting operating units.
Control panel located at machine infeed for operator convenience.
Hot melt granulate glue application system w/ 12 minute heat up time.
Quick change glue tank for easy maintenance and glue color change, scrape and buff units.
Universal automatic magazine for strip and coil feeding, large coil table (800 mm dia) for large coils of 3 mm PVC.
Strengthened precutter for cutting PVC from the coil.
Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing strength.
First pressure roller driven and (2) idle pressure rollers.
Double motor end trimming unit with straight and chamfer capability.
Program controlled indexing from straight to bevel end up to 15 trimmings.
Fine trimming unit w/ digital "Quickset" system.
Includes manual, CD, spanners, (2) grease guns w/ both grease types, hand tools, allen wrenches, smooth and barbed feed wheels, strip-feed fences, additional gluepot heater.
This machine has had continuous regular maintenance and has been serviced by Stiles technicians.
Machine has only 145 hours on meter, machine has been very well cared for and is in excellent condition, ready for...

View Specifications >

		Learn about Machines of Interest to Me >

BRANDT [KD 78 CF] - EDGEBANDER

Inventory #28267

Capacity min./max edge thickness of coiled edge material mm 0.4/3, strips up to mm 12.
Automatic with motorized bottom feeding track (power kW 1.1).
Side-bar (with plastic wheels) for the workpieces supporting.
SIKO readouts for an easy adjustment.
Support for band coil.
Electronic Programmer BS 02.
Equipped with the following working units: No. 2 Rectifiers (pre-milling units) kW 2.2 x 2 at RPM 12000.
Glueing area with Glue Pot and pressing rollers for straight edges.
End cutting units (kW 0.35 x 2 at RPM 12000) turn 0°-15°, pneumatic adjustment.
Rough/Fine trimming units (kW 0.55 x 2 at RPM 12000) tiltable 0°-25°.
With SIKO.
Profiling / Corner Rounding Units (kW 0.35 x 2 at RPM 12000) with pneumatic adjustment according to the kind of process (it works both top and bottom sides) with SIKO.
Edge Scrapers with SIKO.
Buffing unit (kW 0.09 x 2 at RPM 2750).
CE mark.
Safety & sound-proof enclosures...

View Specifications >

		Learn about Machines of Interest to Me >

STEFANI [BETA 6000] - EDGEBANDER WITH CORNER ROUNDING

Inventory #28323

Capacity panel thickness 10 to 60 mm.
Min. panel width 60 mm.
Min. panel length 110 mm.
3/4" max. & 0.016" min. edgebanding cap. and 60 mm max. panel thickness, min. panel width 110 mm.
Set up to handle thin PVC as well as solid wood lipping, Heavy Duty guillotine for 3 mm thick PVC banding.
XILIA SRI programmable PLC line control (no limit switches) for workstation functions and panel thickness setting and feed speed control.
Quick Melt glue system with pre-melt hopper and round underneath glue pot, automatic coil & strip feed magazine, 4-roll pressure section with (1) large diameter driven and (3) idle pneumatically controlled pressure rolls.
Infeed magazine, gluing unit & pressure section tilt 0 - 7°.
Workstations: Front & rear end trim, 0.7 HP - 12,000 RPM motor ea., bevel 0° - 15° horizontally (Y-750).
Top & bottom rough trimming, 2.5 HP - 12,000 RPM motor ea. (R-25), w/quick change mechanism.
Top & bottom fine & radius trimming, 1.4 HP - 12,000 RPM motor ea., bevels 0° to 45° (RSU-14), w/quick change mechanism.
"C 1" and C 2" top & bottom (full 180°) corner rounding unit (4 motors of 0.3 HP - 12,000 RPM ea.), for leading & trailing edge, motors with quick change mounting and tiltable up 20°.
"RCS" top & bottom PVC scraper w/Nebulizer (air/oil) knife cleaning device and special PVC chip collector, 1 mm min. and 5 mm max. radius.
LEISTER 1,400 Watt hot air blowers for reactivating of PVC edge.
Last station: "SPO" top & bottom buffers (0.35 HP - 1770 RPM motors), units tilt 0° - 35°.
Variable feed speed 26 - 72 FPM, feed chain with 80 mm wide rubberized chain pads, dual roller upper holddown beam with motorized height adjustment.
C/W: All trimming stations with SIKO mechanical digital read outs.
Full size, high tech look sound insulated cabins w/windows.
Dust hoods and venting designed to facilitate connection of machine to central dust collection system, outboard panel support, separate control panel w/LED readouts houses the PLC line control, remote "jog" control for easy setup adjustments, FVR frequency inverter.
All electrical components are KLOECKNER MOELLER & UL/CSA...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [OPTIMAT KL 77/A3/S2] - EDGEBANDER WITH PRE-MILLING

Inventory #28291

Capacity max. working panel height with straight edge 60 mm.
Applicable banding material in coils: thin edge and PVC up to 3 mm.
Top pression unit made by motorized rubbered belt.
Top pression unit with adjustable height in automatic by numerical control.
Adjusting in continuos feeding speed with regulation in automatic by numerical control.
Input panel guide is motorized and with adjusting in automatic by numerical control.
Lateral bar with lines of idle wheels to support the panels.
Pre milling unit to rectify the side of the panel.
It is made by 2 motors with automatic in/out intervention to avoid splinters on the panel - motors power 3 kW ( 9000 RPM).
GLUING UNIT, INSERTION AND PRESSION OF THE EDGE.
Multiple magazine for edge coils with nr. 6 positions, to automatically change the edge type.
Hot-melt glue pot lang1045 and premelter.
Spreading roller to regulate the quantity of apllied glue.
Guillotine to cut the edge in coils.
Roller set to press the edge on straight profiles - nr. 1 + 2 pressing rollers - motorized regulation of depth position in automatic by numerical control.
Anti-gluing unit made by 2 guns that spray liquid on the top and bottom part of the panel.
End cutting unit with 2 motors to cut the excess edge on the front and back part of the panel - motors tiltable 0 / 15° - tilting regulation in automatic - motors power 0.18 kW ( 18000 RPM).
Top and bottom rough trimming unit - motors power 0.55 kW ( 12000 RPM).
Double multifunction unit FK 13 with regulation in automatic by numerical control, This unit has a double functions: A) to trim and round off the excess edge B) to round the edge corners on the top and bottom part of the panel - double automatic tool changer with magazine nr. 8 positions - motors power 0.6 kW ( 12000 RPM).
Edge scraping unit for the edge superfinishing - regulation of position in automatic by numerical control.
Glue scraping unit to remove the excess glue from the join between edge and panel.
Air Heating unit to heat the edge and reactevate the colour.
Brushing unit with 2 motors to clean and polish the edge - oscillating system.
Control and program system HOMATIC NC 21 with the following features: - screen colour - keyboard Adjustable hanging command board to control the machine.
Incorporated electrical cabinet .
Security norme CE mark.
Safety and sound-proof enclosure cabinet of the working units.
Dust collection system on the top part of the safety enclosure cabinet.
Automatic system to out-put the wood wastes...

View Specifications >

		Learn about Machines of Interest to Me >

SCM [K208ERT-1] - SINGLE SIDED EDGEBANDER WITH SCRAPING, CORNER ROUNDING

Inventory #28450

Capacity 15/32" (12 mm) max. edge.
2" max. ( w/ corner rounding only 1-3/4") banding height.
2-3/8" min. panel width and 6-5/16" min. length.
RM-K 2 Head pre-milling station model (2.5 HP - 19,000 RPM motors ea.).
Automatic strip and coil feed magazine w/ heavy duty 3 mm PVC cap.
Guillotine.
Glue pot with glue roller application system w/ auto recycling device for unused glue.
Digital thermostat adjustment for temperature control.
3 roll pressure unit w/ pneumatic controls for all pressure rollers - Double front & rear end trim (.4 HP-12,000 RPM motor ea.) tilts 0-15° end trimmers mounted on 45° THK guide.
Top / bottom fine/radius trimmer (.8 HP - 12,000 RPM motors) with quick change/disconnect motors tilts 0-45° - Corner rounding units for top and bottom of leading and trailing corner with edgebanding all (4) sides (two .5 HP - 200 Cy motors ea.).
Unit trims entire panel - Top and bottom PVC scraper for up to 5 mm radius.
Top and bottom buffing unit (.33 HP-2,800 RPM motors) .
Hot air heating unit for PVC/ABS - Single 42 FPM fixed feed speed.
1 HP drive, drive chain with chain pads traveling on round and flat tracks...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [KF 20/12/QA/25] - PVC DOUBLE SIDED COMBINATION TENONER EDGEBANDER

Inventory #28564

Capacity First and second pass double sided combination edgebander.
Equipped with extended infeed Vertical jump milling, Left & right side double hogging, Left & right side Universal Milling/Groving, Right side left side free space double coil edgeband magazine.
Quick melt gluing system.
High speed end trim units right & left side, Top & bottom rough trimming, Left & right side Top & bottom fine trimming.
Left & right side Oscillating buffing.
Left and right side electronic width and height adjustment.
Homatic PLC.
2 m Opening.
Thin tape edgebander.
PVC Coils...

View Specifications >

		Learn about Machines of Interest to Me >

BRANDT [KDN 980 2C] - EDGEBANDER W/CORNER ROUNDING AND RETURN CONVEYOR

Inventory #29560

Capacity 20 mm edge thickness.
80 mm work height.
2 motor End trim, champer.
/straight.
2x 1.85 kW Rough trimming unit and Super Station.
(2) Motor Corner Rounding.
Radius + Glue Line Scraper.
2 x 0.18 kW Buffing Station.
2 x 0.55 kW Fine Trimming unit.
2 X 0.4 kW Contour Trimming unit.
Heat Reactivation unit.
Thomas return conveyor.
PC-16 Program control,auto height adjustment of all work station.
20 m/min. feed speed...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [AKRON 246] - SINGLE SIDED EDGEBANDER

Inventory #29588

Capacity edge thickness of 0.4 to 3 mm with shear cut.
Maximum thickness 12 mm solid wood strips.
Maximum thickness 55 mm.
Minimum height 10 mm sizing.
Double milling group at the entrance to the alignment machine workpiece edge with the machine groups.
Dual Compound motor with reverse rotation system.
Gluing system.
Shear and pressure group.
Group gluer system hotmelt applicator roller.
Group pneumatic shears cutting edge.
Group presser rollers, pneumatic pressure system.
Group tilted trimming saw two motors. adjust incline from CN. - Tilt motors 0/15°s.
Group milling inclined - tilt motors 0/20°s - displays for system control position - Motor power 0.55 kW (12000 RPM).
CR 200 multifunction Group two motors controlled from CN.
Power 0.50 kW (12000 giri / min).
Scrapers with Manual setting.
Brushes group.
Control System 321 machine and NC programming.
System start-stop motor by electronic inverters.
Electrical cabinet included in the machine.
Handheld Programming Console operator position...

View Specifications >

		Learn about Machines of Interest to Me >

BIESSE [AKRON 645] - SINGLE SIDED EDGEBANDER

Inventory #29589

Capacity edge thickness of 0.4 to 3 mm with shear cut.
Maximum thickness 12 mm solid wood strips.
Maximum thickness 55 mm.
Minimum height 10 mm sizing.
Group composed of upper nip roller double row of overlapping.
System regulation with display electric upper nip position.
Side guide manually adjustable support.
Double milling group at the entrance to the alignment machine workpiece edge with the machine groups.
Dual Compound motor with reverse rotation system.
Guing system.
Shear and pressure group.
Group singing gluer system hotmelt applicator roller.
Group pneumatic shears cutting edge.
Group presser rollers.
Pneumatic pressure system.
Group tilted Trimming saw two motors.
Adjust incline from CN. - Tilt motors 0/15°s.
Group milling inclined - tilt motors 0/20°s - displays for system control position - Motor power 0.55 kW (12000 RPM).
CR 200 multifunction Group two motors controlled from CN.
Power 0.50 kW (12000 giri / min).
Scrapers Group Manual setting.
Brushes Group.
Ontrol System 321 machine and NC programming.
System start-stop motor by electronic inverters.
Electrical cabinet included in the machine.
Handheld Programming Console operator position...

View Specifications >

		Learn about Machines of Interest to Me >

HOMAG [KAL 310/6/A20-S2] - 3MM EDGEBANDER W/AUTO RETURN

Inventory #29639

Capacity working level 950 mm (37-13/32"), min. working width w/thickness 22 mm (7/8") 55 mm (2-5/32"), 60 mm (2-3/8") 100 mm (3-15/16"), panel overhang 30 mm (1-1/8"), workpiece thickness min. 12 mm (15/32"), max. 60 mm (2-3/8"), edge thickness strips 0.4 mm to 20 mm (0.16" to 25/32"), coils 0.3 mm to 3 mm (0.12" to 1/8"), processing limits strips 1150 mm2 (1.78 sq. in), coils 135 mm2 (0.19 sq. in).
Open Space for the later addition of a pre-milling unit.
{Panel Pre-Heater Homag Unit #2325, quartz lamp for heating substrate edge before glue application, for improved edge quality and optimum bonding.
Preparation for adaptation of Nordson application unit, provides mounting assembly for Nordson Slot Nozzle, glue reactivation system.
Nordson Glue Application System, per Nordson proposal 04081Q-64-411, BN-20.
5-gallon pail un-loader, EB60V-III 10 to 60 mm (13/32" to 2-3/8") adjustable edge banding slot nozzle.
Multi-Purpose Magazine with Single Coil Horizontal Table, Homag Unit #2999, capable of running coiled material, strips.
And solid wood bands, easily changed from one application to the next with the flip of a switch, conveniently located on the movable control pendant, infeed angle 8°s, edge thickness 0.4 mm to 20 mm (0.016" to 25/32"), edge height 12 mm to 65 mm (15/32" to 2-9/16"), processing limits 900 mm2 (1.39 sq. in), min. edge length 260 mm (10-1/4"), strip capacity approx. 295 mm (11-1/2").
Clipping Unit Homag Unit #2445, designed for today's popular use of thick coil PVC, for use with single-roll table magazine, max. edge thickness 3.5 mm (0.14"), max. edge height 65 mm (2-9/16"), PVC processing limits 135 mm2 (0.19 sq. in.), veneer processing limits 100 mm2 (0.15 sq. in.), max. roll diameter 900 mm (35-7/16").
Magazine Height Adjustment Homag Unit # 2451 , with threaded spindle adjustment and digital readout, adjustable +/- 5 mm (+/- 13/32").
Pressure Zone for Gluing Section Type G Homag Unit #2507, one (1) driven pressure roller 160 mm (6-5/16") diameter, twelve (12) secondary pressure rollers 70 mm (2-3/4") diameter, with pneumatic pressure control for straight edges, centralized manual adjustment for edgeband thickness with digital mechanical counter.
Snipping Unit WK14/0, 8 kW Solid Wood Homag Unit# 3064, for snipping the edge overhang at front and rear edge, upright snipping stop, installed above the machine frame - thus no snipping waste in the snipping unit, workpiece overhang manually adjustable, motors swiveled manually for chamfer snipping, manual adjustment of the snipping stop to different edge thickness, two (2) motors each 0.4 kW, 200 Hz,,12,000 RPM, workpiece overhang min. 30 mm (1-1/8"), edge thickness chamfer / straight max. 3 mm (1/8"), chamfer max. 30°s, snipping depth soft max.20 mm, edge width 65 mm (2-9/16"), edge cross section max. 1000 mm2, feed speed max. 25 m/min., panel distance min. 350 mm, panel sequence front edge/front edge, 25 m/min. (82'/min.) = 1000 mm , panel thickness max. 60 mm, the unit is installed at the machine frame above.
Top / Bottom Flush Trimming Unit Homag Unit #3209, motors positioned one above the other, 1.5 kW.
200 cycle; 12,000 RPM, angle adjustment +/- 1°, with two (2) carbide tipped trimming cutters, 70 mm x 25 mm (2-3/4" x 31/32"), HSK 25, z = 4, motors running against direction of feed, motors manually adjustable with digital mechanical counters, height adjustment with top pressure beam, electronic frequency inverter for control of motor speed and braking, HSK 25 tool interface, motors running with direction of feed.
Latest computer, monitor and modem recently installed.
Homatic PC 22 2 GHz CPU...

View Specifications >

		Learn about Machines of Interest to Me >

Page 1 of 1

<< First Page | < Prev. Page | Next Page > | Last Page >>

* Price may vary with exchange rate.